There's no guarantee that a condition variable is stateful. The docs for
`Condvar::notify_one()` actually say the opposite:
> If there is a blocked thread on this condition variable, then it will be woken
> up from its call to wait or wait_timeout. Calls to notify_one are not buffered
> in any way.
This test was relying on the main loop obtaining the lock and entering the
condition variable sleep before the thread was scheduled and got around to
notifying the condition variable. If this non-deterministic behavior was not
upheld, the test would time out since it would obtain the lock (either before or
after the variable were updated) then call `condvar.wait()` *after* the variable
had been updated and the condvar signalled, but without (atomically or even at
all) checking to see if the desired wake precondition was fulfilled. As the
child thread had already run and the wake notification was NOT buffered, there
was nothing to wake the running thread.
There really wasn't any way to salvage the test as originally written, since the
write to `ctx.val` was not in any way linked to the acquire/release of the mutex
so regardless of whether or not the main thread obtained the mutex and checked
the value precondition before calling `condvar.wait()`, the child thread's write
could have happened after the check but before the wait() call. As such, the
test has been rewritten to use `wait_while()` but then also updated to bail in
case of a timeout instead of hanging indefinitely (since neither the `ctest`
runner nor the `cargo test` harness was timing out; `cargo test` would only
report that the test had exceeded 60 seconds but as long as it was not executed
with `cargo test -- -Z --ensure-time` (which is only available under nightly),
the test would not halt.
If this test were *intentionally* written to test the scenario that was timing
out, it should be written deterministically in such a way that the main loop
did not run until after it was guaranteed that the variable had been updated
(i.e. by looping until val became 5 or waiting for an AtomicBool indicating the
update had completed to be set), but I'm not sure what the benefit in that would
be since the docs actually guarantee the opposite behavior (the notified state
is explicitly not cached/buffered).
If we have fish code written with the assumption that condvar notifications
prior to *any* call to `Condvar::wait()` *are* buffered, then that code should
of course be revisited in light of this.
Commit 8a7c3ce (Don't abandon line after writing control sequences, 2024-04-06)
was broken by 29f2da8 (Toggle terminal protocols lazily, 2024-05-16), fix that.
Fixes#10529
Reminder that reStructuredText is awkward and you can't make sphinx treat these
as inline code; they'll be formatted as italic text only.
Vim search expression:
\([`:]\)\@<!`[^`:]\+`\(`\)\@!
Followed by
ysi``
does the trick quite nicely.
* feat: improve konsole completion
* Improve konsole profile completion to be dynamic
Directly complete --profile as a long argument
* Dynamically complete konsole -p
This makes `path basename` a more useful replacement for the stock `basename`
command, which can be used with `-s .ext` to trim `.ext` from the base name.
Previously, this would have required the equivalent of
path change-extension "" (path basename $path)
but now it can be just
path basename -E $path
* Properly handle a lot more -Z completion formats as suggested by `rustc -Z
help`
* Don't run any `rustc` commands when sourcing `rustc.fish`; these invocations
are instead deferred until the user attempts to complete the specific switch.
* Support CSV -A/F/D/W values
This adds a crate containing a new implementation of printf, ported from musl.
This has some advantages:
- locale support is direct instead of being "applied after".
- No dependencies on libc printf. No unsafe code at all.
- No more WideWrite - just uses std::fmt::Write.
- Rounding is handled directly in all cases, instead of relying on Rust and/or
libc.
- No essential dependency on WString.
- Supports %n.
- Implementation is more likely to be correct since it's based on a widely used
printf, instead of a low-traffic Rust crate.
- Significantly faster.
Mostly replacing std::<type>::MAX with <type>::MAX.
Surprising here is replacing
.expect(format!(...))
with
.unwrap_or_else(|_| panic!(...))
It explains that this is because the "format!" would always be called.
This enabled the profile in fish_setlocale, which caused startup
profile to always be on, so
```fish
fish --profile file -c 'foo'
```
would show the entire startup as well
Hex float parsing may come about through wcstod, for example:
printf "%f" '0x8p2'
should output 32.0.
Currently we use a not-great fork of hexponent. Hexponent has been dormant for
years, and has some issues: doesn't round properly, allocates unnecessarily,
doesn't handle denormals, is more complicated than necessary.
Just rewrite hex float parsing, fixing those problems and getting us off of this
weird fork.
ThreadId is way slower than it should be for the sense that we use it in; it
doesn't cache the id and allocates an Arc internally.
We don't care about the thread id used in crate::threads correlating with any
other thread id the code uses anywhere (not that it does) because it's only used
for our own bookkeeping. Change to something much simpler instead.
Verified that std::sync::OnceLock<T> compiles to the same assembly at the
*access* site as the Option<T> we were using. The additional overhead upon init
is fine. No need for extra Box<T> indirection for IO_THREAD_POOL.
While obtaining an uncontested mutex from the same thread (without reentrance)
is basically ~free, the use of `MainThread<RefCell<T>>` instead of `Mutex<T>`
makes it clear that there is no actual synchronization taking place, hopefully
making the code easier to understand.
We don't set this variable ourselves, but some might set it in their config out
of habit coming from shells that don't automatically colorize ls output.
This variable overrides stdout tty detection for `ls --color=auto` (but does not
modify the behavior of `ls --color=never` or `ls --color=always` regardless of
its value) under at least the BSD version of `ls`. (Under the GNU version, it
influences colorization only if stdout *is* a tty.)
If we detect CLICOLOR_FORCE *and* we are not writing directly to the tty, we
skip colorization (by clearing-but-not-erasing `$__fish_ls_color_opt`, so that
we don't end up accidentally using its value from another scope).
This automatically assigns the 'completions' label and the 'fish next-3.x'
milestone to completions-only PRs.
A completions-only PR is defined as being one that touches
share/completions/*.fish but does not touch any files outside of share/
